FUTABA T6K V3 + R3008SB RECEIVER (mode-2)

An eight-channel Futaba RC kit using the T-FHSS Air-2.4GHz telemetry transmission system for recreational and sport modelers. The transmitter can also be switched to S-FHSS transmission mode and thus use a range of S-FHSS receivers (without telemetry) from the miniature six-channel R2106GF to the eight-channel R2008SB. With the R3008SB receiver attached, you have 8 PWM channels for classic servos or 8 channels via the S.BUS and S.BUS2 buses, as well as telemetry data on the receiver's power supply voltage and signal strength captured by the receiver. Additional telemetry data can be obtained from additional telemetry sensors connected to the S.BUS2 bus.

The T6K V3S transmitter, in a case that fits perfectly in the hand, is equipped with precision cross-control with lock/neutral adjustment, 4 switches, 4 digital trimmers and a rotary proportional controller. Three buttons and a multifunction joystick are used for programming; a backlit LCD display provides easy orientation in the intuitive menu. The T6K V3S has memory for 30 models and a wide range of mixing functions for aerobatic aircraft, gliders, helicopters and multicopters. In addition to displaying telemetry data on the display, a voice telemetry output (not included) is available in the handset jack. The T6K is also equipped with a teacher-student jack, and allows programming and setting of S.BUS servos.

To run the transmitter, you will need 4 AA alkaline batteries or rechargeable NiMH batteries stored in the holder supplied with the transmitter, or a 4-5-cell NiMH or 2S LiFe battery.

FEATURES

• T-FHSS Air-2.4GHz transmission system with telemetry, S-FHSS 2.4GHz without telemetry
• 8 proportional channels
• Precision cross controllers (transmitters are available in 1 or 2 mode, easy to upgrade, and easy to completely cancel throttle lock and have cross controllers neutralized in all axes for drones or tanks)
• Rotary proportional controller, 4 three-position switches, 4 digital trimmers
• Assignable mix switches, freely assignable controls for channels 5-8
• Programs for aerobatics of model airplanes, gliders, helicopters and multicopters
• Upgradable software (requires CIU-3 USB interface)
• S.BUS server programming slot
• Multifunction joystick and three buttons for easy programming
• Telemetry voice output to headphone jack (3.5mm jack)
• Vibration signaling
• Backlit LCD display 128x64 pixels
• Memory for 30 models
• Gas extinguishing function
• Servo tester and monitor with graphic representation of servo deviations
• Resetting model data
• Model copying
• Safe emergency deflection
• Trim step setting/trim reset
• slave
• Reversing the direction of servo deflection
• Student teacher
• Two timers (stopwatch or timer) activated by switch or throttle

Program menu for aerobatic aircraft

• Set size and direction of deflection, double deflection and exponential deflection
• 4 freely programmable mixes (3 linear, one with 5-point curve)
• Flaperons with adjustable differentiation
• Differentiation of aileron deflection
• Gyro gain control
• Aerodynamic brake
• Mix elevator flaps
• Mix flap-elevator mix

Glider program menu

• 6 types of wings (1-2 ailerons, 1-4 flaps), 2 types of tail surfaces
• Set size and direction of deviations, double and exponential deviations
• 4 freely programmable mixes (3 linear, one with 5-point curve)
• 4 flight modes
• Flaperons
• Differentiation of aileron deflection
• Butterfly mix
• Mix camber (trailing edge curvature)
• Mix elevator-camber
• Mix Motor (motor control via switch with adjustable start and stop)
• Gyro gain control
• Mix ailerons and flaps
• Trim mix

Menu of helicopter programs

• 6 types of cycling board
• Set size and direction of deflection, double deflection and exponential deflection
• 4 freely programmable mixes
• 4 flight modes with adjustable delay
• 5-point throttle curves
• 5-point collective curves
• Automatic rotation
• Gyro gain control
• Revomix
• Throttle delay
• Governor
• Deviation and correction correction for cyclic board

Program menu for multicopters

• Set size and direction of deviations, double deviations and exponential deviations
• 6 freely programmable mixes
• 5-point throttle curve
• Gyro gain control
• Throttle position signaling
• Throttle delay

Compatible telemetry sensors

• Temperature sensor (SBS-01T)
• Temperature sensor (SBS-01TE)
• Tachometer with optical sensor (SBS-01RO)
• Tachometer with magnetic sensor (SBS-01RM)
• Tachometer for AC motors (SBS-01RB)
• Voltage sensor (SBS-01V)
• Current sensor (SBS-01C)
• Barometric altimeter/variometer (SBS-01A, SBS-02A)

RC KIT INCLUDES

• Futaba T6K V3S 2.4 GHz transmitter
• R3008SB receiver
• Switch with charging cable
• Plastic screwdriver
  

*Follow the included instructions